xf86config ce ti resiti problem...

XFree86 4.1, koji čini mi se dolazi po defaultu uz Slack 8, ne podržava S3 kartice (a i nema XF86Setup, neko valjda xf86conf ili tako nešto, to su promenili). Instaliraj X 3.3.6.

Pa to vas i pitam, kako da obrisem ovaj i instaliram stariji???
Ako moze detaljno objasnjenje
P.S. Imam instalacioni CD Slackware 7.1

1. pkgtool ( uklonis problematican paket )
2. installpkg ( dodas siguran paket )

Evo potpuni info o podrzanosti S3 kartica pod XFree86 v 3.3.6 i 4.1.0:

3.3.6:
Support (accelerated) for the S3 911, 924, 801, 805, 928, 864, 868, 964, 968, Trio32, Trio64, Trio64V+, Trio64UV+, Aurora64V+, Trio64V2, PLATO/PX is provided by the XF86_S3 server and the XF86_SVGA server with the s3_svga driver. Support (accelerated) for the ViRGE, ViRGE/VX, ViRGE/DX, ViRGE/GX, ViRGE/GX2, ViRGE/MX, ViRGE/MX+ is provided by the XF86_S3V server. Support (accelerated) for those ViRGE chips, as well as the Trio3D and Trio3D/2X is provided by the XF86_SVGA server with the s3v driver. Support (accelerated) for the Savage3D, Savage3D/MV, Savage4, and Savage2000, is provided by the XF86_SVGA server with the s3_savage driver on some OSes (Linux, *BSD).

4.1.0:
Support (accelerated) for the ViRGE, ViRGE/VX, ViRGE/DX, ViRGE/GX, ViRGE/GX2, ViRGE/MX, ViRGE/MX+, Trio3D and Trio3D/2X is provided by the "s3virge" driver. Support (accelerated) for the Savage3D, Savage3D/MV, Savage4, and Savage2000, is provided by the "savage" driver. Support for the other S3 chipsets has not yet been ported.

Aha, ipak podržava neke chipsete. Znam da ne podržava moju S3 Trio64V+, al to sam gledao davno pa mi je nekako ostalo u sećanju kao da ne podržava ni jednu S3 Trio karticu. Izvinjavam se, moja greška. Nemoj da deinstaliraš X 4.1 :o).

A šta je sa akceleracijom na TNT i TNT2 based karticama, koji drajver treba koristiti pod 4.x i 3.x verzijom X-a?

Mislis na ovo : ?

NVIDIA

3.3.6:
Support (accelerated) for the NV1, Riva 128, 128ZX, TNT, TNT2 (Ultra, Vanta, M64), GeForce (DDR, 256) and Quadro is provided by the XF86_SVGA server and the nv driver.

4.1.0:
Support (accelerated) for the Riva 128, 128ZX, TNT, TNT2 (Ultra, Vanta, M64), GeForce (DDR, 256), GeForce 2 (GTS, Ultra, MX), GeForce 3, Quadro, and Quadro2 is provided by the "nv" driver.

Summary:
All chipsets supported in 3.3.6 except the NV1 are also supported in 4.1.0. Support for the newer chips (GeForce2 and later) is only available in 4.1.0.

NVIDIA drajveri za Slackware
http://www.nvidia.com/docs/lo/...UPP/NVIDIA_GLX-1.0-1541.tar.gz
http://www.nvidia.com/docs/lo/.../NVIDIA_kernel-1.0-1541.tar.gz

Procitaj sledeci dokument vezan za instalaciju drajvera ..:
http://www.nvidia.com/docs/lo/1018/SUPP/NVLinuxNotes_1541.pdf

Ostali drajveri

RedHat 7.1, one CPU, uniprocessor kernel

http://www.nvidia.com/docs/lo/...P/NVIDIA_GLX-1.0-1541.i386.rpm
http://www.nvidia.com/docs/lo/...ernel-1.0-1541.rh71up.i386.rpm

Mandrake 8.0, one CPU, uniprocessor kernel

http://www.nvidia.com/docs/lo/...P/NVIDIA_GLX-1.0-1541.i386.rpm
http://www.nvidia.com/docs/lo/...rnel-1.0-1541.mdk80up.i386.rpm

SuSE 7.2

http://www.nvidia.com/docs/lo/...A_GLX-1.0-1541.suse72.i386.rpm
http://www.nvidia.com/docs/lo/...ernel-1.0-1541.suse72.i386.rpm

Source RPMS

http://www.nvidia.com/docs/lo/...PP/NVIDIA_GLX-1.0-1541.src.rpm
http://www.nvidia.com/docs/lo/...NVIDIA_kernel-1.0-1541.src.rpm

[Ovu poruku je menjao Tigerheart dana 10-04-2001 u 07:48 AM GMT]

Nikako ne mogu da podesim X !!! Instalirao sam XFree86 3.3.6 koji u slack 7.1
podesim bez problema, ali opet ista prica, stalno mi izbacuje neke greske!!Tipa
"ne mogu da pronadjem monitor" !!
Jel moze neko da napise step-by-step uputstvo kako da resim ovaj problem!!
Vidim da 4.1. takodje podrzava s3 trio 3d , tako da mi nikako ne ide u glavu
zasto pod slack 8.0 nece da radi ni 4.1 ni 3.3.6 ??
Ili mozda ja negde DEBELO gresim. Sto je najverovatnije! :)

????
Odkud sad druga priča ??
Oću da piškim, neću da piškim .....

Verovatno je greška do tebe .... ako ništa onda uzmi i ukucaj originalna osvežavanja koja ti pišu u uputstvu za monitor

Ne baš, pre bih nešto nevezano za OS a vezano za XFree86..

kako druga prica?? pa od pocetka govorim da je problem u tome,sto
nikako ne mogu da podesim x u slackware 8.0, a da sam pre toga imao slack 7.1
koji mi radio bez problema! Pa sam zato pitao kako da instaliram stari
XFree86 3.3.6 u slack-u 8.0!! i napokon kad sam posle svega i to uspeo opet
dobijam istu gresku (iako sve podesim identicno kao i u 7.1)...
zato bih vas zamolio da neko od vas napise koje sve pakete treba da obrisem i
koje nove(mislim na stari XFree86 3.3.6) da dodam, pa da onda vidim da li ce sve raditi kako treba!
A sto se tice monitora, u tome i jeste problem sto imam neki krs i to bez
uputstva!