U biosu treba da ti stoji upaljena opcija za dual channel memoriju i da ako nisi dirao napon rama da stavis auto!

Sve je bilo na auto, napone nisam dirao. Pokusao sam i ovako pod Advanced Memory Settings, ali je rezultat isti.

Performance Enhance: Normal
DRAM Timing Selectable: Quick
Channel Interleaving: Enabled
Rank Interleaving: Enabled



Google:
-------------------
Quote from the manual:
"When enabling Dual Channel mode with two or four memory modules, it is recommended that memory
of the same capacity, brand, speed, and chips be used and installed in the same colored DDR3 sockets. For optimum performance, when enabling Dual Channel mode with two memory modules, we recommend that you install them in the DDR3_1 and DDR3_2 sockets."

Maybe you could also check if you have Channel Interleaving and Rank Interleaving both set as enabled, also the setting Performance Enhance set to Extreme, again under Advanced Memory Settings. Channel Interleaving should have a positive effect when you have installed memory modules according to the Dual Channel advice given in the manual.

Google:
-------------------
I can't even start the system while the ram kit is inserted in blue/blue or white/white (Dual channel config), it is peeping 20 times then reboot peeping again, reboot--> infinite loop.

it is not the ram, I tested every single ram in every single slot, I tested also different ram from my old build, everything is working despite the setup in dual channel mode.

So I contacted Gigabyte Support, they told in this case the cpu memory controller is faulty! So the cpu or the cpu socket is damaged? Some pins are damaged?
-------------------



_{[Ovu poruku je menjao walden dana 02.02.2013. u 20:56 GMT+1]}

1. Da li si racunar sklapao ti, ili je sklopljen tamo gde si ga kupio?
2. Ako si ti sklapao racunar, da li si stavio module u odgovarajuce DIMM slotove da bi radili u dual channelu (Pogledati korisnicko uputstvo da se vidi sta preporucuje Gigabyte. Kod njih je to dobro obradjeno u korisnickim uputstvima. Sve pise, ako ne u glavnim tezama, onda postoje fusnote.)?
3. Ako je rec o XMP ready memoriji, kao sto najverovatnije jeste, ne moras nista rucno da cackas u BIOS-u od dodatnih podesavanja za memoriju, vec samo treba da aktiviras adekvatan XMP profil u Extreme Memory Profle (X.M.P.) i sve bi trebalo da proradi kako treba.

_{[Ovu poruku je menjao Binary Mind dana 03.02.2013. u 16:27 GMT+1]}

Nisam, jeste



Prebacio sam module u odgovarajuće slotove po uputstvu, ali u tom slučaju neće da se podigne sistem.
(short beeps kako god da ih postavim, osim DDR3_2 + DDR3_4) - svi slotovi su cisti, nema nikakvih ostecenja...
...naime sistem nece da se podigne kada se postave u dual channel (kada se stave u single channel sve radi...



Nije XMP, nemam tu opciju u BIOSu. Samo dva-tri HyperX blue modela su XMP ready http://www.kingston.com/us/memory/hyperx/blu
http://www.kingston.com/datasheets/KHX1600C9D3B1_4G.pdf

Mislio sam da se radi o uparenim XMP ready modulima, mada je opet malo cudno da masina nece da se digne kad stavis module u DIMM slotove 1 i 2. Moralo bi da radi. Nesto tu izgleda nije u redu. Mirise na nesto u vezi sa montiranjem procesora, mada to ti ne bi trebalo da diras pogotovu ako nemas iskustva da montiranjem LGA procesora u LGA socket. Ostaje ti da reklamiras masinu, i pitas zasto nece memorija da radi u dual channel rezimu.