[ dejantt @ 29.12.2017. 20:00 ] @
||Pozdrav,imam problem sa gore navedenom masinom,naime,pustim je da radi,primi vodu i tu stane i stoji beskonacno dugo.ne krece da vrti bubanj,ne daje nikakve znake zivota,bez obzira na koji program da je stavim.ima li neko ideju sta bi moglo da joj bude?hvala unapred...|
[ gmhans @ 29.12.2017. 22:20 ] @
[ test1234 @ 29.12.2017. 22:30 ] @
[ avdo2503 @ 03.01.2018. 15:15 ] @
Pozdrav,da li neko ima za gorenje ves masinu WA50080 tablicu blinkanja led lampica. Hvala
[ test1234 @ 03.01.2018. 21:42 ] @
Evo za Gorenje veš mašine, greške :
Washing machine temperature sensor fault
The washing machine has detected a problem with the water heating temperature sensor and although the program will complete the machine will not heat the water.
Check wiring to temperature sensor or thermistor
Check thermistor or temperature sensor
Replace thermistor if faulty
Check wiring at control module or timer
Door lock fault detected
The door lock on the washing machine has been detected as faulty or failed to engage correctly.
Check that the washing machine door has been closed correctly and is engaging the door lock correctly
Check wiring to door lock
Check door lock
Check wiring at control module or timer
Washing machine water intake has failed to reach level
The water level was not detected as reaching the correct level by the pressure sensor.
Check water supply is on and that there is sufficient water pressure available
Check water intake valve wiring and electrical connections
Check pressure sensor wiring and electrical connections
Check water inlet valve
Check water level or pressure sensor
Check connections to the main control module or timer
Inverter cannot control the motor
The inverter card, motor speed and voltage electronic control module cannot control the motor speed. Please note that this code would only be displayed on models that have an brushless motor fitted.
Check connections and wiring between the inverter card and the motor
Check the motor tacho is complete and in place
Check the main control PCB
Replace inverter card if no fault found on the motor
Washing machine control card and inverter card cannot communicate
The main control module cannot communicate with the motor speed control board or inverter card.
Ordinarily when this error is reported the fault will lie in the wiring or with the inverter card and not the control module, which is reporting the error correctly.
Check wiring loom between the main control card and inverter card
Check connector blocks at both cards
Replace inverter card
Washing machine water heating element detected faulty
A fault has been detected in the water heating circuit which would ordinarily mean that the wash heater is open circuit.
Check wiring and connections to the water heating element
Check heating element for continuity
Check thermostat or thermistor wiring and connections
Check thermostat or thermistor
Check connections on main control module
Washing machine failed to drain
The washing machine has failed to drain the water and will stop with water in it.
Drain the washing machine manually before proceeding with any diagnostics.
Check pump filter for any obstruction or foreign objects
Check drain outlet hose for any blockage or obstruction
Check drain pump for continuity
Check drain pump rotor is good
Check wiring to pump and connections to the drain pump
Check connection to the main control module
Washing machine motor fault detected
A fault has been detected with the washing machine's main motor although no specific indication of the nature is offered.
Check all connections to the main drive motor
Check motor tacho unit
Check motor carbon brushes where used
Check motor armature
Check connections to the main control module
Leak detected on washing machine models with Aquastop fitted
This fault code is only used on Gorenje washing machine models that have their Aquastop leak detection system fitted and will not show on models that do not have this feature.
Check for any leaks and resolve
Check Aquastop inlet hose
Check connections to Aquastop inlet hose
Check connections to float leak detection device if fitted
Check connections to main control module
[ avdo2503 @ 04.01.2018. 07:45 ] @
Copyright (C) 2001-2018 by www.elitesecurity.org. All rights reserved.