[ kalkulus @ 07.10.2005. 23:42 ] @
kada pokusham da narezem CD-RW koji sam minut pre toga obrisao, proverio da li je prazan i sve je ok, k3b prijavljuje Input/Output greshke i posle toga drajv nece da cita CDove. ovo je drugi drajv u 3 dana sa kojim sam probao i isto se deshava. koristio sam isti CD-RW ali nisam nikada cuo da losh disk upropasti drajv. ako vec ne valja kako ga je onda obrisao koristim Slackware 10.2, kernel 2.4.31. ne koristim scsi emulaciju vec cdrecord koristi opciju dev=ATAPI:0,0,0 evo shta kaze cdrecord dev=ATAPI -scanbus [CODE] kalkulus@meanX:~$ cdrecord dev=ATAPI -scanbus Cdrecord-Clone 2.01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling scsidev: 'ATAPI' devname: 'ATAPI' scsibus: -2 target: -2 lun: -2 Warning: Using ATA Packet interface. Warning: The related Linux kernel interface code seems to be unmaintained. Warning: There is absolutely NO DMA, operations thus are slow. Using libscg version 'schily-0.8'. scsibus0: 0,0,0 0) '_NEC ' 'DVD_RW ND-3540A ' '1.01' Removable CD-ROM 0,1,0 1) * 0,2,0 2) * 0,3,0 3) * 0,4,0 4) * 0,5,0 5) * 0,6,0 6) * 0,7,0 7) * [/CODE] evo debug data iz k3b-a [CODE] System ----------------------- K3b Version: 0.12 KDE Version: 3.4.2 QT Version: 3.3.4 Kernel: 2.4.31 Devices ----------------------- _NEC DVD_RW ND-3540A 1.01 (/dev/hdc, ) at /cdrom [CD-R; CD-RW; CD-ROM; DVD-ROM; DVD-R; DVD-RW; DVD-R DL; DVD+R; DVD+RW; DVD+R DL] [DVD-ROM; DVD-R Sequential; DVD-R Dual Layer Sequential; DVD-RW Restricted Overwrite; DVD-RW Sequential; DVD+RW; DVD+R; DVD+R Double Layer; CD-ROM; CD-R; CD-RW] [SAO; TAO; RAW; SAO/R96R; RAW/R96R; Restricted Overwrite] Used versions ----------------------- cdrecord: 2.1 cdrecord ----------------------- scsidev: 'ATAPI:/dev/hdc' devname: 'ATAPI:/dev/hdc' scsibus: -2 target: -2 lun: -2 Warning: Using ATA Packet interface. Warning: The related Linux kernel interface code seems to be unmaintained. Warning: There is absolutely NO DMA, operations thus are slow. SCSI buffer size: 64512 /usr/bin/cdrecord: This version of cdrecord does not include DVD-R/DVD-RW support code. /usr/bin/cdrecord: If you need DVD-R/DVD-RW support, ask the Author for cdrecord-ProDVD. /usr/bin/cdrecord: Free test versions and free keys for personal use are at ftp://ftp.berlios.de/pub/cdrecord/ProDVD/ Cdrecord-Clone 2.01 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg Schilling TOC Type: 1 = CD-ROM Using libscg version 'schily-0.8'. Driveropts: 'burnfree' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : '_NEC ' Identifikation : 'DVD_RW ND-3540A ' Revision : '1.01' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: 0x000A Profile: 0x002B Profile: 0x001B Profile: 0x001A Profile: 0x0015 Profile: 0x0014 Profile: 0x0013 Profile: 0x0011 Profile: 0x0010 Profile: 0x000A (current) Profile: 0x0009 Profile: 0x0008 (current) Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R Drive buf size : 1343488 = 1312 KB FIFO size : 4194304 = 4096 KB Track 01: data 637 MB Total size: 732 MB (72:33.22) = 326492 sectors Lout start: 732 MB (72:35/17) = 326492 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 2 Reference speed: 6 Is not unrestricted Is erasable Disk sub type: High speed Rewritable (CAV) media (1) ATIP start of lead in: -11077 (97:34/23) ATIP start of lead out: 359849 (79:59/74) 1T speed low: 4 1T speed high: 10 2T speed low: 2 2T speed high: 10 power mult factor: 2 6 recommended erase/write power: 5 A1 values: 24 2C DC A2 values: 14 A4 4A A3 values: 04 C4 80 Disk type: Phase change Manuf. index: 11 Manufacturer: Mitsubishi Chemical Corporation Blocks total: 359849 Blocks current: 359849 Blocks remaining: 33357 Starting to write CD/DVD at speed 10 in real SAO mode for single session. Last chance to quit, starting real write in 2 seconds. 1 seconds. 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. BURN-Free is OFF. Turning BURN-Free on Performing OPC... Sending CUE sheet... /usr/bin/cdrecord: WARNING: Drive returns wrong startsec (0) using -150 Writing pregap for track 1 at -150 Starting new track at sector: 0 Track 01: 0 of 637 MB written. /usr/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 01 F0 00 00 1F 00 status: 0x0 (GOOD STATUS) cmd finished after 10.104s timeout 200s /usr/bin/cdrecord: A write error occured. /usr/bin/cdrecord: Please properly read the error message above. /usr/bin/cdrecord: Input/output error. test unit ready: scsi sendcmd: retryable error CDB: 00 00 00 00 00 00 status: 0xa (Reserved) Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 04 01 00 80 D0 36 Sense Key: 0x2 Not Ready, Segment 0 Sense Code: 0x04 Qual 0x01 (logical unit is in process of becoming ready) Fru 0x0 Sense flags: Blk 0 (not valid) operation 81% done cmd finished after 22.060s timeout 200s /usr/bin/cdrecord: Input/output error. test unit ready: scsi sendcmd: retryable error CDB: 00 00 00 00 00 00 status: 0xa (Reserved) Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 04 01 00 80 FF FF Sense Key: 0x2 Not Ready, Segment 0 Sense Code: 0x04 Qual 0x01 (logical unit is in process of becoming ready) Fru 0x0 Sense flags: Blk 0 (not valid) operation 99% done cmd finished after 22.170s timeout 200s write track data: error after 1015808 bytes Writing time: 72.639s Average write speed 72.3x. Fixating... /usr/bin/cdrecord: Input/output error. flush cache: scsi sendcmd: retryable error CDB: 35 00 00 00 00 00 00 00 00 00 status: 0xa (Reserved) Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 3A 00 00 80 FF FF Sense Key: 0x2 Not Ready, Segment 0 Sense Code: 0x3A Qual 0x00 (medium not present) Fru 0x0 Sense flags: Blk 0 (not valid) operation 99% done cmd finished after 2.000s timeout 200s /usr/bin/cdrecord: Caught interrupt. Trouble flushing the cache BURN-Free was never needed. /usr/bin/cdrecord: fifo had 80 puts and 17 gets. /usr/bin/cdrecord: fifo was 0 times empty and 5 times full, min fill was 95%. cdrecord command: ----------------------- /usr/bin/cdrecord -v gracetime=2 dev=ATAPI:/dev/hdc speed=10 -dao driveropts=burnfree -eject -data /d/Temp/slackware.10.2_1.iso [/CODE] evo shta kaze dmesg [CODE] Linux version 2.4.31 (root@meanX) (gcc version 3.3.6) #4 Thu Oct 6 20:35:07 CEST 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 131056 zone(0): 4096 pages. zone(1): 126960 pages. zone(2): 0 pages. ACPI: RSDP (v000 KT400A ) @ 0x000f71d0 ACPI: RSDT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: MADT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7fc0 ACPI: DSDT (v001 KT400A AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 Kernel command line: BOOT_IMAGE=Linux-novi ro root=302 Initializing CPU#0 Detected 1533.211 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 3060.53 BogoMIPS Memory: 515464k/524224k available (1740k kernel code, 8372k reserved, 592k data, 108k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000 CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000 CPU: AMD Athlon(tm) XP 1800+ stepping 02 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ACPI: IRQ9 SCI: Level Trigger. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch ([email protected]) mtrr: detected mtrr type: Intel ACPI: Subsystem revision 20040326 PCI: PCI BIOS revision 2.10 entry at 0xfbae0, last bus=1 PCI: Using configuration type 1 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: System [ACPI] (supports S0 S1 S4 S5) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Via IRQ fixup ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *5 ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled. ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled. ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled. ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled. PCI: Probing PCI hardware ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 PCI: Using ACPI for IRQ routing Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket BIOS EDD facility v0.11 2004-Jun-21, 2 devices found Starting kswapd VFS: Disk quotas vdquot_6.5.1 Journalled Block Device driver loaded Detected PS/2 Mouse Port. pty: 512 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A Real Time Clock Driver v1.10f Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) PPP generic driver version 2.4.2 Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 439M agpgart: Detected Via Apollo Pro KT400 chipset agpgart: unable to determine aperture size. Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 00:0f.0 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci00:0f.0 ide0: BM-DMA at 0xa800-0xa807, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xa808-0xa80f, BIOS settings: hdc:pio, hdd:pio hda: WDC WD2000JB-00GVA0, ATA DISK drive hdb: QUANTUM FIREBALLlct20 30, ATA DISK drive blk: queue c0391e60, I/O limit 4095Mb (mask 0xffffffff) blk: queue c0391f9c, I/O limit 4095Mb (mask 0xffffffff) hdc: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 390721968 sectors (200050 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100) hdb: attached ide-disk driver. hdb: host protected area => 1 hdb: 58633344 sectors (30020 MB) w/418KiB Cache, CHS=3649/255/63 hdc: attached ide-cdrom driver. hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 Partition check: hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 > hdb: hdb1 hdb2 hdb3 < hdb5 hdb6 > Via 686a/8233/8235 audio driver 1.9.1-ac3 via82cxxx: Six channel audio available PCI: Setting latency timer of device 00:11.5 to 64 ac97_codec: AC97 codec, id: ALG96 (Unknown) via82cxxx: Codec rate locked at 48Khz via82cxxx: board #1 at 0xBC00, IRQ 11 usb.c: registered new driver usbdevfs usb.c: registered new driver hub Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 108k freed Adding Swap: 514072k swap-space (priority -1) Adding Swap: 208804k swap-space (priority -2) EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal EXT3-fs: mounted filesystem with ordered data mode. NTFS driver v1.1.22 [Flags: R/O MODULE] kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,66), internal journal EXT3-fs: mounted filesystem with ordered data mode. NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6111 Tue Jul 27 07:55:38 PDT 2004 via-rhine.c:v1.10-LK1.1.19 July-12-2003 Written by Donald Becker http://www.scyld.com/network/via-rhine.html eth0: VIA VT6102 Rhine-II at 0xc000, 00:04:61:61:7e:c4, IRQ 11. eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000. ehci_hcd 00:10.4: VIA Technologies, Inc. USB 2.0 ehci_hcd 00:10.4: irq 11, pci mem e0d05000 usb.c: new USB bus registered, assigned bus number 1 ehci_hcd 00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4 hub.c: USB hub found hub.c: 8 ports detected usb-uhci.c: $Revision: 1.275 $ time 20:28:28 Oct 6 2005 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: USB UHCI at I/O 0xac00, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 4 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: USB UHCI at I/O 0xb800, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 5 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (4095 buckets, 32760 max) - 288 bytes per conntrack ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A PPP BSD Compression module registered PPP Deflate Compression module registered spurious 8259A interrupt: IRQ7. ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A PPP BSD Compression module registered PPP Deflate Compression module registered ISO 9660 Extensions: Microsoft Joliet Level 3 ISOFS: changing to secondary root ISO 9660 Extensions: Microsoft Joliet Level 1 ISOFS: changing to secondary root hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Cannot read medium - incompatible format -- (asc=0x30, ascq=0x02) The failed "Send DVD Structure" packet command was: "ad 00 00 00 00 00 00 00 00 20 00 00 " hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid field in parameter list -- (asc=0x26, ascq=0x00) The failed "Mode Select 10" packet command was: "55 10 00 00 00 00 00 00 3c 00 00 00 " Error in command data byte 12 hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid field in parameter list -- (asc=0x26, ascq=0x00) The failed "Mode Select 10" packet command was: "55 10 00 00 00 00 00 00 3c 00 00 00 " Error in command data byte 12 hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid field in parameter list -- (asc=0x26, ascq=0x00) The failed "Mode Select 10" packet command was: "55 10 00 00 00 00 00 00 3c 00 00 00 " Error in command data byte 12 hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid command operation code -- (asc=0x20, ascq=0x00) The failed "<NULL>" packet command was: "3c 00 00 00 00 00 00 00 04 00 00 00 " hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid field in parameter list -- (asc=0x26, ascq=0x00) The failed "Mode Select 10" packet command was: "55 10 00 00 00 00 00 00 10 00 00 00 " Error in command data byte 7 hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Cannot read medium - incompatible format -- (asc=0x30, ascq=0x02) The failed "Send DVD Structure" packet command was: "ad 00 00 00 00 00 00 00 00 20 00 00 " hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid field in parameter list -- (asc=0x26, ascq=0x00) The failed "Mode Select 10" packet command was: "55 10 00 00 00 00 00 00 3c 00 00 00 " Error in command data byte 12 hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid field in parameter list -- (asc=0x26, ascq=0x00) The failed "Mode Select 10" packet command was: "55 10 00 00 00 00 00 00 3c 00 00 00 " Error in command data byte 12 hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid field in parameter list -- (asc=0x26, ascq=0x00) The failed "Mode Select 10" packet command was: "55 10 00 00 00 00 00 00 3c 00 00 00 " Error in command data byte 12 hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid command operation code -- (asc=0x20, ascq=0x00) The failed "<NULL>" packet command was: "3c 00 00 00 00 00 00 00 04 00 00 00 " hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 hdc: irq timeout: status=0xd0 { Busy } hdc: irq timeout: error=0xd0LastFailedSense 0x0d hdc: DMA disabled hdc: ATAPI reset complete hdc: packet command error: status=0x51 { DriveReady SeekComplete Error } hdc: packet command error: error=0x54 ATAPI device hdc: Error: Illegal request -- (Sense key=0x05) Invalid field in parameter list -- (asc=0x26, ascq=0x00) The failed "Mode Select 10" packet command was: "55 10 00 00 00 00 00 00 10 00 00 00 " Error in command data byte 7 cdrom: open failed. [/CODE] i za kraj lspci -v, ako nekoga zanima IDE kontroler [CODE] 00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge (rev 80) Subsystem: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP] Host Bridge Flags: bus master, 66Mhz, medium devsel, latency 8 Memory at e8000000 (32-bit, prefetchable) [size=64M] Capabilities: [80] AGP version 3.5 Capabilities: [c0] Power Management version 2 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00 [Normal decode]) Flags: bus master, 66Mhz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: ec000000-edffffff Prefetchable memory behind bridge: e0000000-e7ffffff Capabilities: [80] Power Management version 2 00:0f.0 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE Flags: bus master, medium devsel, latency 32, IRQ 11 I/O ports at a800 [size=16] Capabilities: [c0] Power Management version 2 [/CODE] bicu zahvalan za bilo kakvu pomoc, poludecu [Ovu poruku je menjao kalkulus dana 08.10.2005. u 00:45 GMT+1] |