[ marciko @ 09.04.2006. 10:04 ] @
Instaliran Slackware 10.2 kernel 2.6.15 sa podrškom za ppp, modem rs232 us.robotics v92 exerni na ttyS0, pokušaću da objasnim ukratko šta me muči: Trebalo bi na linuxu da radi dial'in server za konekciju sa jednim računarom za update baze podataka. Probao sam da podesim dial-in pomoću uugetty-ja (Mgetty nikako nisam uspeo da podignem, javlja error 2 canot write echo\n), modemi rade kad se ručno javim iz minicom-a sa komandom ata, pa mislim da je problem do neke konfiguracije mislim da nije do kernel-a ili modema. Konfiguracija fajlova koje mislim da on koristi izgledaju ovako: /etc/inittab # inittab This file describes how the INIT process should set up # the system in a certain run-level. # # Version: @(#)inittab 2.04 17/05/93 MvS # 2.10 02/10/95 PV # 3.00 02/06/1999 PV # 4.00 04/10/2002 PV # # Author: Miquel van Smoorenburg, <[email protected]> # Modified by: Patrick J. Volkerding, <[email protected]> # # These are the default runlevels in Slackware: # 0 = halt # 1 = single user mode # 2 = unused (but configured the same as runlevel 3) # 3 = multiuser mode (default Slackware runlevel) # 4 = X11 with KDM/GDM/XDM (session managers) # 5 = unused (but configured the same as runlevel 3) # 6 = reboot # Default runlevel. (Do not set to 0 or 6) id:3:initdefault: # System initialization (runs when system boots). si:S:sysinit:/etc/rc.d/rc.S # Script to run when going single user (runlevel 1). su:1S:wait:/etc/rc.d/rc.K # Script to run when going multi user. rc:2345:wait:/etc/rc.d/rc.M # What to do at the "Three Finger Salute". ca::ctrlaltdel:/sbin/shutdown -t5 -r now # Runlevel 0 halts the system. l0:0:wait:/etc/rc.d/rc.0 # Runlevel 6 reboots the system. l6:6:wait:/etc/rc.d/rc.6 # What to do when power fails. pf::powerfail:/sbin/genpowerfail start # If power is back, cancel the running shutdown. pg::powerokwait:/sbin/genpowerfail stop # These are the standard console login getties in multiuser mode: c1:1235:respawn:/sbin/agetty 38400 tty1 linux c2:1235:respawn:/sbin/agetty 38400 tty2 linux c3:1235:respawn:/sbin/agetty 38400 tty3 linux c4:1235:respawn:/sbin/agetty 38400 tty4 linux c5:1235:respawn:/sbin/agetty 38400 tty5 linux c6:12345:respawn:/sbin/agetty 38400 tty6 linux # Local serial lines: #s1:12345:respawn:/sbin/agetty -L ttyS0 9600 vt100 #s2:12345:respawn:/sbin/agetty -L ttyS1 9600 vt100 # Dialup lines: #d1:12345:respawn:/sbin/agetty -mt60 38400,19200,9600,2400,1200 ttyS0 vt100 #d2:12345:respawn:/sbin/agetty -mt60 38400,19200,9600,2400,1200 ttyS1 vt100 # Runlevel 4 used to be for an X window only system, until we discovered # that it throws init into a loop that keeps your load avg at least 1 all # the time. Thus, there is now one getty opened on tty6. Hopefully no one # will notice. ;^) # It might not be bad to have one text console anyway, in case something # happens to X. x1:4:wait:/etc/rc.d/rc.4 #2:123:respawn:/sbin/agetty -w -I 'ATE0Q1&D2&C1S0=\013' 115200 ttyS0 vt100 #s1:2345:respawn:/sbin/uugetty ttyS0 56000 vt100 -x 8 #debug 8 #S0:2345:respawn:/sbin/mgetty -n 2 ttyS0 #S1:2345:respawn:/sbin/mgetty -D ttyS1 #S2:2345:respawn:/sbin/mgetty -D ttyS2 #S3:2345:respawn:/sbin/mgetty -D ttyS3 S0:3:respawn:/sbin/uugetty -d /etc/conf.uugetty.ttyS0 ttys0 38400 vt100 /etc/conf.uugetty.ttyS0 ALTLOCK=/dev/ttyS0 # probao sam i sa cua0 INITLINE=/dev/ttyS0 # takođe TIMEOUT=60 INIT="" \d+++\dAT\r OK\r\n ATH0\r OK\r\n AT\sM0\sE1\sQ0\sV1\sX4\ATS0=2\r OK\r\n WAITFOR=RING CONNECT="" ATA\r CONNECT\s\A DELAY=1 #DEBUG=010 /etc/options.server -detach asyncmap 0 modem crtscts lock proxyarp ms-dns 192.168.10.1 ms-dns 192.168.111.30 ms-dns 10.0.57.3 192.168.11.10:192.168.11.1 a na drugom računaru sa drugim (potpuno istim modemom) sam konfigurisao vezu pomoću ppp-setup, i računar neće da se jevi na dolayeći poziv, da li neko može da mi objasni gde sam pogrešio??? |