[ Stator @ 29.04.2006. 13:28 ] @
| Upravao sam kupio no name usb hub sa 4 porta. Na Windows-u mi radi super dok me na Linux-u malko zeki :) Code: stator@bender ~ $ uname -a Linux bender 2.6.15-gentoo-r7 #7 Fri Apr 28 16:43:36 CEST 2006 x86_64 AMD Athlon(tm) 64 Processor 3200+ GNU/Linux Kada ga utaknem, dmesg mi izbaci ovo, znaci prepoznan je od strane kernela Code: usb 1-1: new high speed USB device using ehci_hcd and address 13 hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected Ona ubacim moj usb disk koji inace super radi kada se direktno utakne i dmesg kaze ovo Code: ehci_hcd 0000:00:02.1: qh ffff81003f9c51e0 (#00) state 4 scsi8 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 14 usb-storage: waiting for device to settle before scanning Vendor: CORNICE Model: Inc. Storage Ele Rev: 042R Type: Direct-Access ANSI SCSI revision: 00 SCSI device sdb: 2858688 512-byte hdwr sectors (1464 MB) sdb: assuming drive cache: write through SCSI device sdb: 2858688 512-byte hdwr sectors (1464 MB) sdb: assuming drive cache: write through sdb: sdb1 sd 8:0:0:0: Attached scsi disk sdb usb-storage: device scan complete E sada ide onaj zabavni deo, kada ga mountujem i pokusam da mu pristupim jednostavno on pokaze da je prazan Code: hub 1-1:1.0: cannot reset port 3 (err = -71) hub 1-1:1.0: hub_port_status failed (err = -71) hub 1-1:1.0: cannot reset port 3 (err = -71) hub 1-1:1.0: cannot reset port 3 (err = -71) hub 1-1:1.0: cannot reset port 3 (err = -71) hub 1-1:1.0: Cannot enable port 3. Maybe the USB cable is bad? hub 1-1:1.0: cannot disable port 3 (err = -110) hub 1-1:1.0: cannot reset port 3 (err = -110) hub 1-1:1.0: cannot reset port 3 (err = -110) hub 1-1:1.0: cannot reset port 3 (err = -110) I gomila ovakvih gresaka (c/p sam sam jedan mali deo) Code: end_request: I/O error, dev sdb, sector 2446368 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446369 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446370 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446343 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446343 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446423 end_request: I/O error, dev sdb, sector 2446424 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446423 FAT: Directory bread(block 2446360) failed sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446424 FAT: Directory bread(block 2446361) failed sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446425 FAT: Directory bread(block 2446362) failed sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446426 FAT: Directory bread(block 2446363) failed sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446427 FAT: Directory bread(block 2446364) failed sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446428 FAT: Directory bread(block 2446365) failed sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446429 FAT: Directory bread(block 2446366) failed sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446430 FAT: Directory bread(block 2446367) failed sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 796 FAT: FAT read failed (blocknr 733) hub 1-1:1.0: hub_port_status failed (err = -110) sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 5639 printk: 38 messages suppressed. Buffer I/O error on device sdb1, logical block 5576 lost page write due to I/O error on sdb1 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 5640 Buffer I/O error on device sdb1, logical block 5577 lost page write due to I/O error on sdb1 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2102791 Buffer I/O error on device sdb1, logical block 2102728 lost page write due to I/O error on sdb1 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2446327 Buffer I/O error on device sdb1, logical block 2446264 lost page write due to I/O error on sdb1 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2102791 sd 8:0:0:0: SCSI error: return code = 0x70000 end_request: I/O error, dev sdb, sector 2102791 FAT: Directory bread(block 2102728) failed Jos jedanput napominjem da mi pod win-om radi bez greske? Ima li neko ideju sta da radim? |