[ kefalo @ 25.06.2008. 14:19 ] @
| Tema bi trebala biti zanimljiva jer evo na forumu je vec hrpa postova tipa "kako ograniciti bandwidth" "kako ADSL+router+LAN".... Ne razumijem se bash u routing pa bi mi trebala vasa pomoc. A kasnije kada ovo proradi napravio bi sazetak ove teme u jedan howto koji bi mogao da se okaci kao sticky thread. Opis problema: Na net idem iz studentskog doma i problem je sto smo ograniceni sa protokom od 60kbps po ip adresi. Postavio sam slackware server u mrezu i sad hocu preko quagga da namjestim dinamicki routing da moj komp korisiti 2 rute, "mojkomp>network gateway>internet" i "mojkomp>slackserver>network gateway>internet". Postoji li mogucnost da podesim quagga router tako da mi spaja ta 2 linka? Znaci 60kbps+60kbps=120kbps ili je samo moguce da ih koristim posebno? Npr. skidam 2 fajla, jedan idem preko prve rute 60kbps i kad krenem drugi da skidam on ide preko druge rute isto 60kbps? internet | router(gateway 192.168.0.250) | \ 192.168.1.84(mojkomp) 192.168.1.30(slackserver) |--------------------------backbone----------------| 10.10.11.1(mojkomp virtual interface eth0:0) 10.10.11.3(slackserver virtual interface eth0:0) Koliko sam skontao trebaju mi daemons zebra, bgpd i ospfd i to sve na mom kompu a na slackserver samo treba da ukljucim routing izmedju 2 interface-a eth0 i eth0:0. Ili grijesim? Evo conf fajlova: Code: root@papastrumpf:/usr/local/etc# cat zebra.conf ! -*- zebra -*- ! hostname papastrumpf !password hehe enable password hehe ! ! Interface's description. ! interface eth0 no shutdown ip address 192.168.1.84/32 link-detect interface eth0:0 no shutdown ip address 10.10.11.1/32 link-detect line vty no login log stdout errors log file /var/log/quagga/zebra.log Code: root@papastrumpf:/usr/local/etc# cat bgpd.conf ! hostname papastrumpf bgp config-type cisco password hehe enable password hehe !interface eth0 ! ip address 192.168.1.84/32 ! no shutdown ! link-detect ! !interface eth0:0 ! ip address 10.10.11.1/32 ! no shutdown ! link-detect router bgp 64584 bgp router-id 192.168.1.84 no synchronization redistribute ospf neighbor 10.10.11.3 remote-as 64530 neighbor 192.168.1.84 remote-as 64584 no auto-summary line vty no login Code: root@papastrumpf:/usr/local/etc# cat ospfd.conf ! -*- ospf -*- ! hostname papastrumpf password hehe enable password hehe router ospf router-id 192.168.1.84 redistribute connected network 10.10.11.0/24 area 0.0.0.0 network 192.168.0.0/16 area 0.0.0.10 line vty no login log stdout errors log file /var/log/quagga/ospfd.log conf fajlovi su sintaksno u redu, pri pokretanju demona ne javljaju se greske vezane za conf fajlove, ali mi javlja ovu gresku zebra. Code: root@papastrumpf:/usr/local/etc# zebra -d Can't up interface root@papastrumpf:/usr/local/etc# ps -ef |grep zebra root 19197 15658 0 15:11 pts/7 00:00:00 grep zebra root@papastrumpf:/usr/local/etc# ifconfig eth0 Link encap:Ethernet HWaddr 00:19:b9:54:8c:7e inet addr:192.168.1.84 Bcast:192.168.255.255 Mask:255.255.0.0 inet6 addr: fe80::219:b9ff:fe54:8c7e/64 Scope:Link UP BROADCAST NOTRAILERS RUNNING MULTICAST MTU:1500 Metric:1 RX packets:625786 errors:0 dropped:0 overruns:0 frame:0 TX packets:577887 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:565438840 (539.2 MiB) TX bytes:334104940 (318.6 MiB) Interrupt:18 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:200 (200.0 B) TX bytes:200 (200.0 B) a kada podignem interface rucno Code: ifconfig eth0:0 10.10.11.1/24 up ne javi mi gresku Can't up interface, ali se ni daemon ne pokrene. Moze malo smjernica sta kako kuda?  hvala [Ovu poruku je menjao kefalo dana 25.06.2008. u 15:32 GMT+1] |