[ Lucky2001 @ 30.01.2004. 05:27 ] @
| Serviserski modovi za televizore ,nesto malo sto ja imam ,ukoliko znate neke nove postujte ovde. Samo pazljivo rukovanje sa nekim od ovih ,ozbiljno moze da poremeti rad tog Tv aparata ,samo pazljivo sa setovanjima. TV Service Modes Name Model/Chassis Fault Repair Advice GRUNDIG CUC2050 chassis Parental lock Using this function, you may enter a number code which blocks all functions. Activating parental lock: Call up the » DIALOG CENTER « using buttons "i" and "OK". Select and call up the line » Parental lock «. Enter a number code with the number buttons 0 …, always using four digits (e.g. 1111). Save the number code with "OK" . The key appears in red, switch off the page » PARENTAL LOCK« with button "TXT" . After switching off the set and switching on again the page » Parental lock « appears, all functions are locked. Switching off parental lock : Switch on the set. Enter a number code with the number buttons 0…9 , always using four digits (e.g. 1111). The set switches to the TV screen. After switching off again the parental lock is activated again. To cancel the parental lock function, select and call up the line “Parental lock” from the » DIALOG CENTER «. Enter the number code with four digits and press button "AUX". GRUNDIG CUC2058 Hotel Mode Activating the Hotel Mode Call up the dialog line "Hotel"with button "i" via "DIALOG CENTER" –>"SERVICE"–>Service Code "8500". With activated "Hotel Mode": -it is no longer possible to call up the "DIALOG CENTER"menu with button "i ". -the last volume setting is stored as the maximum level possible. Deactivating the Hotel Mode Depress and hold button "i "on the remote control handset while switching the TV set on with the mains switch.Under the "SERVICE" menu switch the Hotel Mode off. GRUNDIG CUC2059 Hotel Mode Activating the Hotel Mode Call up the dialog line "Hotel"with button "i" via "DIALOG CENTER" –>"SERVICE"–>Service Code "8500". With activated "Hotel Mode": -it is no longer possible to call up the "DIALOG CENTER"menu with button "i ". -the last volume setting is stored as the maximum level possible. Deactivating the Hotel Mode Depress and hold button "i "on the remote control handset while switching the TV set on with the mains switch.Under the "SERVICE" menu switch the Hotel Mode off. GRUNDIG CUC2080 Hotel Mode Activating the Hotel Mode Call up the dialog line "Hotel"with button "i" via "DIALOG CENTER" –>"SERVICE"–>Service Code "8500". With activated "Hotel Mode": -it is no longer possible to call up the "DIALOG CENTER"menu with button "i ". -the last volume setting is stored as the maximum level possible. Deactivating the Hotel Mode Depress and hold button "i "on the remote control handset while switching the TV set on with the mains switch.Under the "SERVICE" menu switch the Hotel Mode off. GRUNDIG CUC2030 Replacement of NVM 1. After any repair or replacement of NVM (IC82005) check whether the NTSC 3.58MHz quartz is fitted. If it is not, the dialog line "NTSC 3,6" in the Service Menu must be set to "off". Button " i " –> "OK" –> "SERVICE" –> "OK" –> Service Code "8500" –> NTSC 3,6 "off" and in dialog line "End" store the setting "with mem.". GRUNDIG CUC2050 Replacement of NVM 1. After any repair or replacement of NVM (IC82005) check whether the NTSC 3.58MHz quartz is fitted. If it is not, the dialog line "NTSC 3,6" in the Service Menu must be set to "off". Button " i " –> "OK" –> "SERVICE" –> "OK" –> Service Code "8500" –> NTSC 3,6 "off" and in dialog line "End" store the setting "with mem.". GRUNDIG CUC2080 Replacement of NVM 1. After any repair or replacement of NVM (IC82005) check whether the NTSC 3.58MHz quartz is fitted. If it is not, the dialog line "NTSC 3,6" in the Service Menu must be set to "off". Button " i " –> "OK" –> "SERVICE" –> "OK" –> Service Code "8500" –> NTSC 3,6 "off" and in dialog line "End" store the setting "with mem.". GRUNDIG CUC2058 Replacement of NVM 1. After any repair or replacement of NVM (IC82005) check whether the NTSC 3.58MHz quartz is fitted. If it is not, the dialog line "NTSC 3,6" in the Service Menu must be set to "off". Button " i " –> "OK" –> "SERVICE" –> "OK" –> Service Code "8500" –> NTSC 3,6 "off" and in dialog line "End" store the setting "with mem.". GRUNDIG CUC2059 Replacement of NVM 1. After any repair or replacement of NVM (IC82005) check whether the NTSC 3.58MHz quartz is fitted. If it is not, the dialog line "NTSC 3,6" in the Service Menu must be set to "off". Button " i " –> "OK" –> "SERVICE" –> "OK" –> Service Code "8500" –> NTSC 3,6 "off" and in dialog line "End" store the setting "with mem.". GRUNDIG CUC1981 chassis Emergency Data The processor IC850 in this TV receiver is fitted with two memories in which the picture geometry data are stored. If this IC fails or the data have been changed, the TV receiver must be switched on the emergency data set. Emergency Data Loading the Emergency Data :Press and hold the "P-"button on the local keyboard and switch the TV on with the mains button. In doing so, the data sets for the picture geometry values, the deflection and chrominance data are loaded from the keyboard control unit into the respective modules. Subsequently, call up the Info Center Menu - Special Functions - Service - Code Number 8500 - Geometry and change the setting if requested. To store the data Call up "end without mem." and select "End with mem." using the buttons < or >. Initialisiation of the uP (IC8500) (eg. After changing the uP IC 850) - Connect Pin 1 of the processor to chassis and switch the TV on with the mains switch to load the EEPROM in the processor IC850 GRUNDIG CUC2050 Hotel Mode Activating the Hotel Mode Call up the dialog line "Hotel"with button "i" via "DIALOG CENTER" –>"SERVICE"–>Service Code "8500". With activated "Hotel Mode": -it is no longer possible to call up the "DIALOG CENTER"menu with button "i ". -the last volume setting is stored as the maximum level possible. Deactivating the Hotel Mode Depress and hold button "i "on the remote control handset while switching the TV set on with the mains switch.Under the "SERVICE" menu switch the Hotel Mode off. GRUNDIG CUC2030 chassis Parental lock Using this function, you may enter a number code which blocks all functions. Activating parental lock: Call up the » DIALOG CENTER « using buttons "i" and "OK". Select and call up the line » Parental lock «. Enter a number code with the number buttons 0 …, always using four digits (e.g. 1111). Save the number code with "OK" . The key appears in red, switch off the page » PARENTAL LOCK« with button "TXT" . After switching off the set and switching on again the page » Parental lock « appears, all functions are locked. Switching off parental lock : Switch on the set. Enter a number code with the number buttons 0…9 , always using four digits (e.g. 1111). The set switches to the TV screen. After switching off again the parental lock is activated again. To cancel the parental lock function, select and call up the line “Parental lock” from the » DIALOG CENTER «. Enter the number code with four digits and press button "AUX". GRUNDIG CUC2058 chassis Parental lock Using this function, you may enter a number code which blocks all functions. Activating parental lock: Call up the » DIALOG CENTER « using buttons "i" and "OK". Select and call up the line » Parental lock «. Enter a number code with the number buttons 0 …, always using four digits (e.g. 1111). Save the number code with "OK" . The key appears in red, switch off the page » PARENTAL LOCK« with button "TXT" . After switching off the set and switching on again the page » Parental lock « appears, all functions are locked. Switching off parental lock : Switch on the set. Enter a number code with the number buttons 0…9 , always using four digits (e.g. 1111). The set switches to the TV screen. After switching off again the parental lock is activated again. To cancel the parental lock function, select and call up the line “Parental lock” from the » DIALOG CENTER «. Enter the number code with four digits and press button "AUX". GRUNDIG CUC2059 chassis Parental lock Using this function, you may enter a number code which blocks all functions. Activating parental lock: Call up the » DIALOG CENTER « using buttons "i" and "OK". Select and call up the line » Parental lock «. Enter a number code with the number buttons 0 …, always using four digits (e.g. 1111). Save the number code with "OK" . The key appears in red, switch off the page » PARENTAL LOCK« with button "TXT" . After switching off the set and switching on again the page » Parental lock « appears, all functions are locked. Switching off parental lock : Switch on the set. Enter a number code with the number buttons 0…9 , always using four digits (e.g. 1111). The set switches to the TV screen. After switching off again the parental lock is activated again. To cancel the parental lock function, select and call up the line “Parental lock” from the » DIALOG CENTER «. Enter the number code with four digits and press button "AUX". GRUNDIG CUC2080 chassis Parental lock Using this function, you may enter a number code which blocks all functions. Activating parental lock: Call up the » DIALOG CENTER « using buttons "i" and "OK". Select and call up the line » Parental lock «. Enter a number code with the number buttons 0 …, always using four digits (e.g. 1111). Save the number code with "OK" . The key appears in red, switch off the page » PARENTAL LOCK« with button "TXT" . After switching off the set and switching on again the page » Parental lock « appears, all functions are locked. Switching off parental lock : Switch on the set. Enter a number code with the number buttons 0…9 , always using four digits (e.g. 1111). The set switches to the TV screen. After switching off again the parental lock is activated again. To cancel the parental lock function, select and call up the line “Parental lock” from the » DIALOG CENTER «. Enter the number code with four digits and press button "AUX". GRUNDIG CUC2030 chassis Cancelling the Parental Lock To cancel the parental lock enter the number 7038 GRUNDIG CUC2050 chassis Cancelling the Parental Lock To cancel the parental lock enter the number 7038 GRUNDIG CUC2058 chassis Cancelling the Parental Lock To cancel the parental lock enter the number 7038 GRUNDIG CUC2059 chassis Cancelling the Parental Lock To cancel the parental lock enter the number 7038 GRUNDIG CUC2030 Hotel Mode Activating the Hotel Mode Call up the dialog line "Hotel"with button "i" via "DIALOG CENTER" –>"SERVICE"–>Service Code "8500". With activated "Hotel Mode": -it is no longer possible to call up the "DIALOG CENTER"menu with button "i ". -the last volume setting is stored as the maximum level possible. Deactivating the Hotel Mode Depress and hold button "i "on the remote control handset while switching the TV set on with the mains switch.Under the "SERVICE" menu switch the Hotel Mode off. GRUNDIG CUC2080 chassis Cancelling the Parental Lock To cancel the parental lock enter the number 7038 NOKIA Compact B-E2 Digital chassis Service Mode First Method - set with CCU11 uPC: press buttons from remote controls "mon-stereo" - "C" - "hypersonic" whithin 1 sec. Tha display shows "SE". NOKIA Compact B-E2 Digital chassis Service Mode First Method - set with CCU12 uPC: press the contact behind the small borehall on set front pannel (controls) and then button "S" whithin 5 sec. Tha display shows "SE". PHILIPS TV/VCR chassis Hotel Mode Activation Select program 38, press "SELECT" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off-on the TV set. De-Activation Select program 38, then press "SELECT" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec.. When de-activation is OK, a "H-" is displayed. To remove this display turn off-on the TV set. PHILIPS ANUBIS A chassis 2 local controls Hotel Mode First Method Activation Select program 38, press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off-on the TV set. De-Activation Select program 38, then press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When de- activation is OK, a "H-" is displayed. To remove this display turn off-on the TV set.' PHILIPS ANUBIS A chassis 2 local controls Hotel Mode Third Method Activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When activated "HOTEL MODE" a green "H" is displayed. To remove this display turn off-on the TV set. De-activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When de-activation is OK, a green "H" is displayed. To remove this display , turn off-on the TV set. PHILIPS ANUBIS A chassis 8 local controls Hotel Mode First Method Activation Select program 38, press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off-on the TV set. De-Activation Select program 38, then press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When de- activation is OK, a "H-" is displayed. To remove this display turn off-on the TV set.' PHILIPS ANUBIS A chassis 8 local controls Hotel Mode Second Method Activation Select program 38, then press simultaneously "INSTALL" and "PROGRAM+" on local keyboard. De-Activation Select program 38, then press simultaneously "INSTALL" and "CONTROL" on local keyboard. PHILIPS ANUBIS A chassis 8 local controls Hotel Mode Third Method Activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When activated "HOTEL MODE" a green "H" is displayed. To remove this display turn off-on the TV set. De-activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When de-activation is OK, a green "H" is displayed. To remove this display , turn off-on the TV set. PHILIPS G8 chassis Hotel Mode Activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "ON" De-activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "OFF" PHILIPS G8.1ECO chassis Hotel Mode Activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "ON" De-activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "OFF" PHILIPS AA5 chassis Hotel Mode HOTEL MODE Activation Select program 38, press "MENU" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off -on the TV set. De-Activation Select program 38, then press "MENU" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When de-activation is OK, a "H-" is displayed. To remove this display turn off -on the TV set. PHILIPS G8.1 chassis Hotel Mode Activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "ON" De-activation Select "Video2" mode. Press the remote control control keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the displayed Hotel Menu "HOTEL MODE" must be set "OFF" PHILIPS GR1-AX (8 buttons) Hotel mode for models with uP TMP47C434N-R221 Select program 38 on the TV Simultaneously press the STORE key on the TV and SLEEPTIMER on the remote for 4 about seconds (toggles hotel mode) Notes: The maximum volume in hotel mode will be the volume present when activating it STORE or INSTALL mode can not be entered The program number is displayed on the screen for 4 seconds A green 'H' appears in the left bottom of the screen, which can be removed by powering down the TV and powering it up again PHILIPS ANUBIS A chassis 2 local controls Hotel Mode Second Method Activation Select program 38, then press simultaneously "INSTALL" and "PROGRAM+" on local keyboard. De- Activation Select program 38, then press simultaneously "INSTALL" and "CONTROL" on local keyboard. PHILIPS L6.1 (without Teletext) Hotel mode Select program 38 on the TV Simultaneously press the - key on the keyboard of the TV and the OSD key of the remote control PHILIPS GR2.X Service Mode Short circuit pins M33 and M34 before powering up the TV. When powered up the TV LED will show as orange after which the short circuit can be removed. SER will be displayed on screen. Now press simultaneously keys INSTALL and PROG+ on the keyboard of the TV to activate the service menu PHILIPS GR1-AX (8 buttons) Hotel mode for models with uP TMP47C434N-3414/3415, uP TMP47C634N-R494 Select program 38 on the TV Simultaneously press the STORE key and the PROGRAM+ key on the TV for 4 about seconds (hotel mode on) Simultaneously press the STORE key and the CONTROL- key on the TV for 4 about seconds (hotel mode off) Notes: The maximum volume in hotel mode will be the volume present when activating it STORE or INSTALL mode can not be entered The program number is displayed on the screen for 4 seconds PHILIPS ANUBIS B Service Mode Second method: With the TV powered off (disconnected from the mains!) short circuit pins M61 and M62 (next to IC7600). Power up the TV and remove the short circuit. A 'S' will be displayed indicating it is in service mode Simultaneously press the P- and VOL+ keys on the TV. The screen now shows 'service menu'. To allow hotel mode from being set on and off you have to select Option 2 with the remote and set 'Hotel' to 'on'. Exit the service mode by putting the TV into standby PHILIPS ANUBIS B Service Mode First method: Select program 38 on the TV Simultaneously press the P key and the VOLUME+ key (keyboard/remote) To enable hotel mode you should set 'HO' to 'one' PHILIPS ANUBIS AA Service Mode Short circuit terminals M28 and M29 (IC7710) PHILIPS A10E chassis Service Mode This model also supports the 062596 sequence followed by [i+]/[OSD]. Service default mode is entered using the 062596 sequence, followed by the - button on the TV set itself. Alternatively you can short-circuit pins 9261 and 9262 inside the set and then powering it up PHILIPS 20PV220 Service Mode TV preset 38 Push STOP -button on the remote and the PLAY -button on the TV simultaneously, for 5 seconds You´ll get the service menu on screen Clear EEPROM is the only cure for the problem that all items in installation menu are in ” non active ” mode with red text Close TV from remote, and on again Tune channels again PHILIPS 21PT263A Service Mode Short circuit pin 1 of the EEPROM (24C08) to ground PHILIPS ANUBIS Service Mode Short circuit terminals M31 and M32 (IC7710) PHILIPS 20PT424A Service Mode Short circuit pin 1 of the EEPROM (24C08) to ground Schaub Lorentz SL0014KO CTV-VCR Service Mode To enter SERVICE MODE, Unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and remote control key for more than 2 seconds. The both pressing of set key and remote control key will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 30 minutes before Power On or alternatively, discharge backup capacitor. SCHNEIDER TV8 chassis Service Mode Service-Mode Before being switched to the service mode the unit must be set to a channel with a test pattern. Note: The parameters are stored in changed. Press the red key and the blue key on the remote control simultaneously. Within 5 seconds, press the key P-and the key V+ on the local control panel simultaneously The title SERVICE Vxxx (xxx is for software version), appears in the screen. Keys P+ and P- (program) Call up tuning parameters Keys V+ and V- (volume) Modify tuning parameters Display Operation VP Adjust the vertical swift. HP Adjust the horizontal swift. VP Adjust the vertical picture height. Is the setting range not sufficient the range must change with the point CRT. VL Adjust top and button vertical linearity of screen centre. VB Adjust the intensity of the EHT. VB=24 PA Make vertical lines parallel with screen edge. HA Adjust the horizontal size. CC Adjust vertical lines in corners. Basic setting is 0. Setting should only be changed if PA balance cannot be adjusted satisfactorliy. PT Adjust values so that picture has same with at top and bottom edges or other vertical lines are parallel with each other. R Colour drive adjustment G Colour drive adjustment B Colour drive adjustment S-ADJ Connected a Test-picture with stereo signal to the tuner and adjust the TV. Connected Oscilloscope to Pin of ST601. Adjust to lowest crostalk between the channels. L-ADJ Connect Oscilloscope to Pin 1 of ST601. Connect a Test-picture (antenna level>60dBuV/75Ohm) with stereo signal (27kHz frequenceshift.54% modulation factor) to the tuner and adjust the TV. CRT Gear to vertical deflection. In dependence of the picture tube 0 or 1. GR/G+GL Shows like the Cutoff registration locks of in place. Its useable to adjust G2-adjustment. DELAY Superimpose the luma signal on the chrominance signal. Sharp 51DT25H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off To exit the service mode, press the standby button on the remote control. Sharp 4BS-C Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp 51AT15H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode - 'SERV' appears on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off Sharp 51CS05H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 51DS02H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 51DS05H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 59CS03H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 37AT25H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode - 'SERV' appears on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off Sharp 51DS03H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 4BS-B Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 4BSA Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB 4. Press the MODE button on the remote control 5. 'SERV' will appear on the screen 6. Remove the jumper wire To select an adjustment use the channel up and down buttons To change the data press the data buttons The changes are stored automatically Turn the set off at the mains to exit the service mode. Sharp 37ET35H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off To exit the service mode, press the standby button on the remote control. Sharp 37EM33H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off To exit the service mode, press the standby button on the remote control. Sharp 37DT25H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off To exit the service mode, press the standby button on the remote control. Sharp 37AT25H Cancel child lock 1 with tv switched off hold in both vol -- and prog + on tv 2 switch on tv it is now in service mode 3 use channel + to scroll through menu and stop at n v m (non volatile memory) 4 there will also be a 2 digit number in red on the screen as well as another 2 digit number in green, using the vol + button and at the same time observe the green display change the green number until C5 appears 5 At this point the red display shold show 00 for lock to be of if it shows 01 change to 00 using 0 button 6 switch off the set ps the menu is available for many adjustments take care !!! Sharp 66CS05H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 37AM23H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode - 'SERV' appears on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off Sharp 37AM23H Child Lock removal - pin no not known PRESS VOL - ON TV & CHILD LOCK ON REMOTE TOGETHER , PRESS MODE ON REM, USING CHANNEL +/- TO SELECT CHILD LOCK , SELECT NEW PIN PRESS MODE E Sharp 37AM12H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode - 'SERV' appears on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off Sharp 59CS05H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 37DM23H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off To exit the service mode, press the standby button on the remote control. Sharp DV5135H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video unit. Note that the wire is used just like a passing contact switch 5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp 59CSD8H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp DV6640H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp 66AS06H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp DV6635H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp DV66083H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode Sharp DV6603H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode Sharp DV5105H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video unit. Note that the wire is used just like a passing contact switch 5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp DV5107H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video unit. Note that the wire is used just like a passing contact switch 5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp DV5940H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp DV5131H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB 4. Press the MODE button on the remote control 5. 'SERV' will appear on the screen 6. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp DV3751H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB 4. Press the MODE button on the remote control 5. 'SERV' will appear on the screen 6. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp DV5150H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB 4. Press the MODE button on the remote control 5. 'SERV' will appear on the screen 6. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp DV5161H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB 4. Press the MODE button on the remote control 5. 'SERV' will appear on the screen 6. Remove the jumper wire To select an adjustment use the channel up and down buttons To change the data press the data buttons The changes are stored automatically Turn the set off at the mains to exit the service mode. Sharp DV5165H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp DV5180H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp DV5903H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode Sharp DV59083H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode Sharp DV5932H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp DV5935H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp DV5937H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp DV51083H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode Sharp 66ES05H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 59DS03H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 59DS05H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 59ES03H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 59ES05H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 59ESD7H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 5BSA Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode - 'SERV' appears on the screen 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off Sharp 66AS05H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp 66CS03H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 66DS03H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 66DW18H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp DV3760H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB 4. Press the MODE button on the remote control 5. 'SERV' will appear on the screen 6. Remove the jumper wire To select an adjustment use the channel up and down buttons To change the data press the data buttons The changes are stored automatically Turn the set off at the mains to exit the service mode. Sharp 66ESD7H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp 76DW18H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp BCTVA Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of the service slot on the Video Unit 4. SERVICE SOFTWARE will appear on the screen 5. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp D3000 Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Press the service switch (S1401) located on the Video PWB Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode Sharp CW100 Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp DECO-4 Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video unit. Note that the wire is used just like a passing contact switch 5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp Deco-5 Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver on 4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video unit. Note that the wire is used just like a passing contact switch 5. 'SHARP Software Service Ver' will appear on the screen Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp S3B Chassis Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB 4. Press the MODE button on the remote control 5. 'SERV' will appear on the screen 6. Remove the jumper wire Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. Sharp DV3770H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB 4. Press the MODE button on the remote control 5. 'SERV' will appear on the screen 6. Remove the jumper wire To select an adjustment use the channel up and down buttons To change the data press the data buttons The changes are stored automatically Turn the set off at the mains to exit the service mode. Sharp 66DS05H Service Mode 1. Connect a test pattern to the antenna terminal 2. Tune to this signal 3. Turn the receiver off using the mains button 4. Press the volume down and channel up buttons on the front of the receiver at the same time 5. Keeping these buttons pressed, turn the mains on 6. When the set starts up it will be in service mode 7. Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode. SIEMENS FM550.XX chassis Emergency Data The processor IC850 in this TV receiver is fitted with two memories in which the picture geometry data are stored. If this IC fails or the data have been changed, the TV receiver must be switched on the emergency data set. Emergency Data Loading the Emergency Data :Press and hold the "P-"button on the local keyboard and switch the TV on with the mains button. In doing so, the data sets for the picture geometry values, the deflection and chrominance data are loaded from the keyboard control unit into the respective modules. Subsequently, call up the Info Center Menu - Special Functions - Service - Code Number 8500 - Geometry and change the setting if requested. To store the data Call up "end without mem." and select "End with mem." using the buttons < or >. Initialisiation of the uP (IC8500) (eg. After changing the uP IC 850) - Connect Pin 1 of the processor to chassis and switch the TV on with the mains switch to load the EEPROM in the processor IC850 SONY KV27S45 ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER" To WRITE TO EEPROM "Press" - "MUTING" - "ENTER" To INITIALIZE EEPROM "Press" "8" - "ENTER" ID-0 153, ID-1 27, ID-2 13, ID-3 195, ID-4 31, ID-5 1, ID-6 1, ID-7 64 SONY KV32S25 ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER" To WRITE TO EEPROM "Press" - "MUTING" - "ENTER" To INITIALIZE EEPROM "Press" "8" - "ENTER" ID-0 25, ID-1 21, ID-2 31, ID-3 0, ID-4 27, ID-5 0, ID-6 1, ID-7 0 SONY KV32XBR85 ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER" To WRITE TO EEPROM "Press" - "MUTING" - "ENTER" To INITIALIZE EEPROM "Press" "8" - "ENTER" ID-0 120, ID-1 127, ID-2 126, ID-3 52, ID-4 28, ID-5 NA, ID-6 NA, ID-7 NA SONY KV32V16 ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER" To WRITE TO EEPROM "Press" - "MUTING" - "ENTER" To INITIALIZE EEPROM "Press" "8" - "ENTER" ID-0 120, ID-1 127, ID-2 72, ID-3 36, ID-4 19, ID-5 NA, ID-6 NA, ID-7 NA SONY KV32V65 ID CODES after replace EEPROM On remote control "Press" DISPLAY "5" - "VOLUME +" - "POWER" To WRITE TO EEPROM "Press" - "MUTING" - "ENTER" To INITIALIZE EEPROM "Press" "8" - "ENTER" ID-0 89, ID-1 55, ID-2 175, ID-3 10, ID-4 27, ID-5 141, ID-6 6, ID-7 0 VESTEL 11AK20S CHASSIS Service Mode How to enter and exit the SERVICE Menu: Enter the Main Menu Press the digits 4, 7, 2, and 5, respectively Press MENU key to exit There're two selections in the Service Menu: "ADJUST…" and "OPTIONS…" ADJUST Menu: Move the selection bar on the item "ADJUST…" using the P+ or P- keys, Select the item "ADJUST…" using the < or > keys, The items below will be displayed (one of them at one time), 1) AGC (Automatic Gain Control) 8) HSH (Horizontal Shift) 2) VA1 (Vertical Amplitude for 4:3, 50Hz) 9) WG (White Point GREEN) 3) VA2 (Vertical Amplitude for 16:9, 50Hz) 10) WR (White Point RED) 4) VA3 (Vertical Amplitude for 4:3, 60Hz) 11) WB (White Point BLUE) 5) VA4 (Vertical Amplitude for 16:9, 60Hz) 12) CR (Cut-off Red) 6) VSH (Vertical Shift) 13) CG (Cut-off Green) 7) VL (Vertical Linearity) 14) OSH (OSD Horizontal Position) Kod Sony-ja je ocigldeno da ne treba da koristite reprogramiranje eproma ,vec samo do te sekcije bez Mute i tako dalje! |