[ pokusaj @ 07.05.2004. 23:25 ] @
| Nabavio sam knoppix 3.3 i na moje odusevljenje kada sam ga pokrenuo sa cd-a, prepoznao mi je cable modem (nakacen na USB) kao eth0, posle konfiguracije sve je radilo kako treba. Onda sam odlucio da obrisem suse 9.1 i instaliram knoppix na hard. Instalacija je protekla uspesno, medjutim, iako sam snimio podesavanja, i on ih je ucitao cable modem sad nece da radi. Mislio sam da je do firewall-a, pa sam probao iptables -F, opet nista. Probam opet da podignem sa cd-a, radi ... Kucam dmesg (sa CD-a) i dobijem, izmedjuostalog, Code: CDCEther.c: CDCEther_open failed intr_urb -22 CDCEther.c: eth0: set multicast filters CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti usb-uhci.c: interrupt, status 3, frame# 1031 CDCEther.c: rx status -84 CDCEther.c: BULK IN callback but driver is not active! eth1: link up, 100Mbps, full-duplex, lpa 0x41E1 CDCEther.c: CDCEther_open failed intr_urb -22 CDCEther.c: eth0: set multicast filters CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti usb-uhci.c: interrupt, status 2, frame# 76 CDCEther.c: rx status -84 CDCEther.c: eth0: RX status -84 CDCEther.c: rx status -84 CDCEther.c: eth0: RX status -84 CDCEther.c: rx status -84 CDCEther.c: eth0: RX status -84 CDCEther.c: rx status -84 CDCEther.c: eth0: RX status -84 CDCEther.c: rx status -84 CDCEther.c: eth0: RX status -84 CDCEther.c: rx status -84 CDCEther.c: eth0: RX status -84 usb.c: USB disconnect on device 00:07.2-1 address 2 hub.c: new USB device 00:07.2-1, assigned address 3 CDCEther.c: Ethernet information found at device configuration. Trying to use it anyway. CDCEther.c: Found Header descriptor, CDC version 110. CDCEther.c: Imperfect filtering support - need sw hashing CDCEther.c: Can't use SetEthernetMulticastFilters request CDCEther.c: detected BULK OUT packets of size 64 CDCEther.c: interrupt address: 5 CDCEther.c: interrupt interval: 64 CDCEther.c: eth0: Scientific-Atlanta USB Cable Modem 000A73F1A00D CDCEther.c: eth0: 00:0A:73:F1:A0:0D CDCEther.c: CDCEther_open failed intr_urb -22 CDCEther.c: eth0: set multicast filters CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti usb-uhci.c: interrupt, status 3, frame# 1855 CDCEther.c: rx status -84 CDCEther.c: BULK IN callback but driver is not active! CDCEther.c: write_bulk_callback: device not running CDCEther.c: CDCEther_open failed intr_urb -22 CDCEther.c: eth0: set multicast filters CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti CDCEther.c: eth0: too many MC filters for hardware, using allmulti eth1: link up, 100Mbps, full-duplex, lpa 0x41E1 Iako je izbacio greske, modem radi. Kada ga podignem sa harda dobijem nesto u fazonu Code: IP spoofing : rp_filter CDCEther.c: CDCEther_open failed intr_urb -22 eth1: link up, 100Mbps, full-duplex, lpa 0x41E1 Mozda je do ovog IP spoofinga? Kada kucam ping google.com, ne napise da ne radi mreza, nego cuti... Ajde pomozite da ne bih kupovao jos jednu mreznu .... |